Author: Garcia Diaz, V.A.
Paper Title Page
SUPCAV007 Thick Film Morphology and SC Characterizations of 6 GHz Nb/Cu Cavities 18
 
  • V.A. Garcia Diaz, O. Azzolini, E. Chyhyrynets, G. Keppel, C. Pira, F. Stivanello, M. Zanierato
    INFN/LNL, Legnaro (PD), Italy
  • E. Chyhyrynets
    Università degli Studi di Padova, Padova, Italy
  • D. Fonnesu
    CERN, Meyrin, Switzerland
  • O. Kugeler, D.B. Tikhonov
    HZB, Berlin, Germany
  • R. Valizadeh
    STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
  • M. Vogel
    University Siegen, Siegen, Germany
 
  Funding: European Union’s H2020 Framework Programme under Grant Agreement no. 764879
Thick films deposited in long pulse DCMS mode onto 6 GHz copper cavities have demonstrated the mitigation of the Q-slope at low accelerating fields. The Nb thick films (~40 microns) show the possibility to reproduce the bulk niobium superconducting properties and morpholo-gy characterizations exhibited dense and void-free films that are encouraging for the scaling of the process to 1.3 GHz cavities. In this work a full characterization of thick films by DC magnetometry, computer tomography, SEM and RF characterizations are presented.
 
poster icon Poster SUPCAV007 [1.007 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2021-SUPCAV007  
About • Received ※ 21 June 2021 — Revised ※ 07 July 2021 — Accepted ※ 16 February 2022 — Issue date ※ 08 April 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
SUPTEV002 Application of Plasma Electrolytic Polishing onto SRF Substrates 116
 
  • E. Chyhyrynets, O. Azzolini, R. Caforio, V.A. Garcia Diaz, G. Keppel, C. Pira, F. Stivanello, M. Zanierato
    INFN/LNL, Legnaro (PD), Italy
 
  Funding: Work supported by the INFN CSNV experiment TEFEN. This project has received funding from the Euro-pean Union’s Horizon 2020 Research and Innovation programme under GA No 101004730.
A new promising approach of SRF substrates surface treatment has been studied - Plasma Electrolytic Polishing (PEP). The possible application of PEP can be used not only on conventional elliptical resonators, but also on other components of SRF such as, for example, couplers or Quadrupole resonators (QPRs). However, SRF application of PEP represents a challenge since it requires a different approach to treat the inner surface of elliptical cavities respect to electropolishing. In this work, the main problematics and possible solutions, the equipment, and the polishing system requirements will be shown. A proposed polishing system for 6 GHz elliptical cavities and QPRs will be shown and discussed.
 
poster icon Poster SUPTEV002 [2.710 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2021-SUPTEV002  
About • Received ※ 21 June 2021 — Revised ※ 08 July 2021 — Accepted ※ 12 August 2021 — Issue date ※ 22 April 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
SUPTEV003 Cu/Nb QPR Surface Preparation Protocol in the Framework of ARIES Project 121
 
  • E. Chyhyrynets, O. Azzolini, R. Caforio, V.A. Garcia Diaz, G. Keppel, C. Pira, F. Stivanello
    INFN/LNL, Legnaro (PD), Italy
 
  Funding: Work supported by the INFN CSNV experiment TEFEN. This project has received funding from the European Union’s Horizon 2020 Research and Innovation Pro-gramme under Grant Agreement no. 730871.
The Quadrupole Resonator is a powerful tool for SRF R&D on thin films. It allows to perform Q vs E measurements on flat sample rather than a curved surface of a cavity. For the investigation of SC coatings on copper substrates, e-beam welded Cu/Nb samples have been prepared for the QPR. However, the presence of two metals, in particular at the interface makes proper polishing of both surfaces challenging due the different chemical behaviour of both components. In this work we present the protocol developed for surface preparation of the coexisting Cu and Nb phases and the results obtained for 5 different samples. The work was performed in the framework of the ARIES project.
 
poster icon Poster SUPTEV003 [2.506 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2021-SUPTEV003  
About • Received ※ 21 June 2021 — Revised ※ 08 July 2021 — Accepted ※ 12 August 2021 — Issue date ※ 27 September 2021
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPCAV006 Nb3Sn Films Depositions from Targets Synthesized via Liquid Tin Diffusion 452
 
  • M. Zanierato, O. Azzolini, E. Chyhyrynets, V.A. Garcia Diaz, G. Keppel, C. Pira, F. Stivanello
    INFN/LNL, Legnaro (PD), Italy
 
  The deposition of Nb3Sn on copper cavities is inter-esting for the higher thermal conductivity of copper compared to common Nb substrates. The better heat exchange would allow the use of cryocoolers reducing cryogenic costs and the risk of thermal quench [1]. Magnetron sputtering technology allows the deposi-tion of Nb3Sn on substrates different than Nb, however the coating of substrates with complex geometry (such as elliptical cavities) may require targets with non-planar shape, difficult to realize with classic powder sintering techniques. In this work, the possibility of using the Liquid Tin Diffusion (LTD) technique to produce sputtering targets is explored. The LTD tech-nique is a wire fabrication technology, already devel-oped in the past at LNL for SRF applications [2], that allows the deposition of very thick and uniform coat-ing on Nb substrates even with complex geometry [3]. Improvements in LTD process, proof of concept of a single use LTD target production, and characterization of the Nb3Sn film coated by DC magnetron sputtering with these innovative targets are reported in this work.  
poster icon Poster TUPCAV006 [5.032 MB]  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-SRF2021-TUPCAV006  
About • Received ※ 21 June 2021 — Revised ※ 12 July 2021 — Accepted ※ 23 August 2021 — Issue date ※ 02 September 2021
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)